Top 9 Baikal Giant Dash Miner

*POWER SUPPLY IS NOT INCLUDED*
Bitmain recommends using the APW3++ or APW7 power supply.

AntMiner V9 Specifications:
1. Hash Rate: 4.0 TH/s ±5%
2. Power Consumption: 1027W ±10% (at the wall, with Bitmain PSU, 93% efficiency, 25C ambient temp)
3. Power Efficiency: 0.253 W/GH ±7% (at the wall, with Bitmain PSU, 93% efficiency, 25°C ambient temp)
4. Rated Voltage: 11.60 ~13.00V
5. ASIC Chip: BM1580
6. Dimensions: 301mm(L)*123mm(W)*155mm(H)
7. Cooling: 2x 12038 fans
8. Operating Temperature: 0 °C to 40 °C
9. Network Connection: Ethernet (network cable not included)

Please note the following:
1. Due to the nature of these products, there are higher than normal restocking fees (typically 40%). The restocking fees are typically waived in the event that there is a provable failure within the first 30 days and the warranty has not been voided by overclocking. In the event that you experience a failure, please reach out to the seller immediately so that we can begin troubleshooting with you and/or processing a return.
2. Each AntMiner V9 requires TEN 6-pin PCI-e connectors for 12V DC input (must be very stable power source). There are three hash boards that each require THREE 6-pin PCI-e power connectors and one additional 6-pin PCI-e power connector on the controller. All TEN 6-pin PCI-e power connectors are required. Do not connect more than one PSU to the same hash board to prevent possible damage and instability.
3. Power consumption figures will vary with your PSU’s efficiency, the ambient operating temperature and the accuracy of the power meter.
4. Power supply unit is not included. Bitmain recommends the APW3++ or APW7 power supply for the AntMiner V9.

1. Specs:
(A) Hash rate: 17.0 GH/s ±5%
(B) Power consumption: 970W. Power consumption also depends on your PSU’s efficiency.
(C) Dimensions: 14″ x 5″ x 8″
(D) Hashing algorithm: X11
(E) Compatible Coins: DASH, ADZ, ARC, ATX, BOLI, BOPS, BSC, CANN, CNO, CNT, COXST, CREVA, CRM, DP, ENT, ERY, FAL, GILL, GRN, HCC, HPC, INFX, J-x11, KASH, KURT, LGBTQ, LKC, MAR, MARX, MMM, MND, MUE, OGN, ONX, OZC, PIZZA, PXI, SAND, SEV, SMC, START, TOR, TREAU, UIS-x11, VLTC, XCXT, XVP

2. Due to the nature of these products, there are higher than normal restocking fees (typically 40%). The restocking fees are typically waived in the event that there is a provable failure within the first 30 days and the warranty has not been voided by overclocking. In the event that you experience a failure, please reach out to the seller immediately so that we can begin troubleshooting with you and/or processing a return.

3. *A POWER SUPPLY IS NOT INCLUDED.* The APW3++ PSU is recommended above all other PSUs and works with this device when using regular 110v power or 220v power. One APW3++ PSU can only power a single AntMiner D3.

4. Restocking fees for mining devices are 40%. Fees are typically waived if there is a provable failure within the first 30 days. Overclocking will void all warranties. Reach out to the seller immediately if a failure occurs within 30-days of delivery to begin troubleshooting or processing a return.

Scrypt Mining Hash Rate: 504MH/s (±7% is expected).
Compatible Coins: Litecoin and any other Scrypt-based coins.
Power Consumption: 800W (±10%) at the wall.
Noise level: Loud. Not for desk-top use. Sounds like a vacuum.
Chip quantity per unit: 288 x BM1485.
Rated Voltage: 11.60 ~13.00V.
Operating Temperature: 0C to 40C.
Network Connection: Ethernet (cable not included).

Notes:
1. Due to the nature of these products, there are higher than normal restocking fees (typically 40%). The restocking fees are typically waived in the event that there is a provable failure within the first 30 days. In the event that you experience a failure, please reach out to the seller immediately so that we can begin troubleshooting with you and/or processing a return.
2. Each AntMiner L3+ requires NINE 6-pin PCI-e connectors for 12V DC input (must be very stable power supply) There are four hash boards that require two 6-pin PCI-e connectors each and one additional 6-pin PCI-e connector on the controller. All NINE 6-pin PCI-e connectors are required. Do not connect more than one PSU to the same hash board to prevent possible damage and instability.
3. Power consumption figures will vary with your PSU’s efficiency, the ambient operating temperature and the accuracy of the power meter.
4. Power supply unit is NOT included. Bitmain recommends the APW3++ power supply for the AntMiner L3+.
5. AntMiners are LOUD. The L3+ sounds like a vacuum and is not recommended for use within homes. Many people use basements or sheds, but returns due to noise will be subject to the full restocking fee.
Compatible Coins: Any coin based on the Scrypt algorithm. There are many dozen coins, but the most well known is Litecoin.

Hash Rate: 2000MH/s(±10%)

Special provision

Specifications of the Antminer D3 are as follows: a) Hash rate: Hash rate: 19.3 GH/s (Variation of ±5% is expected) b) Power consumption: 1200W (at the wall, with Bitmain’s APW3 PSU, 93% efficiency, 25°C ambient temp). PSU is INCLUDED! c) Dimensions of the miner: 12.6 x5.12 x 7.5″ d) Hashing algorithm: X11 2. It recommends use of the APW3++ PSU with the Antminer D3. One APW3++ PSU can not power more than one Antminer D3. All PCIe connectors on a hashing board need to be connected to the PSU for the hashboard to operate. Do not connect more than one PSU to the same hashing board! – Please select the correct address for shipping before you submit your order because, the shipping address cannot be changed after the order has been submitted. ALL SALES ARE FINAL: 1. A 180-day warranty is provided starting from November 20, 2017 2. The warranty only applies to the original purchaser who purchased the machine. 3. All sales are final. Strict 50% restocking fee for returns. Do not order if you object to the restocking fee. Customer must inspect and test device upon delivery and contact seller within 48 hours to avoid restocking fees. Must be returned with original packaging. Overclocking, using a third party shipping forwarder, or taking the device out of country will void the warranty. Serial numbers are recorded and returns must match. 4. The following events will void the warranty: a. Customer removes/replaces any components by himself; b. Damage caused by poor power supply, lightning or voltage surges; c. Burnt parts on hash boards or chips; d. Miner/boards/components damage due to water immersion or corrosion due to wet environment. 5. We do not take any responsibility for or compensate for any loss as result of downtime caused by delays in transportation as a result of custom formalities or other reasons.

Fire up your child’s imagination for some LEGO Juniors/4+ The Incredibles 2 toys excitement, with this thrilling 10760 Underminer Bank Heist Easy to Build set, featuring a bank vault with breakaway door, Incredibile vehicle with Starter Brick chassis, Tunneler machine with Starter Brick chassis and spinning drill bits, plus a street build with brick wall, wanted poster and buildable streetlamp. This fun super heroes toy also includes a simple guide to build and play, to help build confidence in children. Includes 3 minifigures.

Shipping at Feb 20-28 Blake256R14/Blake256R8/Blake2B/Lbry/Pascal Hash Rate:please check below spec chart Power supply:ATX Power（12V 6Pin connector * 6） Interface:1 X Ethernet Temp Operation：0 ~ 40 ℃ Dimension：312mm(L) x 125mm(W) x 130(H) Weight：3800g

Blake256R14/Blake256R8/Blake2B/Lbry/Pascal Hash Rate:please check below spec chart Power supply:ATX Power（12V 6Pin connector * 6） Interface:1 X Ethernet Temp Operation：0 ~ 40 ℃ Dimension：312mm(L) x 125mm(W) x 130(H) Weight：3800g